Digit OCR on stm or esp from onboard camera
Scansione di un'immagine, riconoscimento delle posizioni delle cifre, taglio dell'immagine a una cifra, ridimensionamento dell'immagine a 2 colori, OCR digitale, trasmissione dei risultati al PC via e-mail o RF diretta.
In this project you must do this tasks:
- scan an image (I will give you some images) in these images there are numbers
- recognize number positions
- cut the image to leave only a digit
- resampling image to 2 color depth
- OCR the image to recover the real number in it in BCD
- send the BCD and the cutted image files to a remote pc.
You can use any low power, low cost device for this purpose.
You can't use pc as recognition server. OCR must be done on microprocessor embedded device.
There are more tasks to do that I don't explain now.
Due to ultra low power performances I preffer to use STM32 instead of ESP32.
My informations are that STM32 (STM32 L4+) absorbs 1uA while ESP32 absorbs 170uA in ultra low power mode.
I need to use it in battery operated long time installation and 170uA is too much to ensure 10 yrs life.
-
21 dni5346 PLN
644 9 0 21 dni5346 PLN
Hello
1. STM32L476 (420 nA Standby mode with RTC to wake up regulary)
2. OmniVision camera (2640/7725 etc.. with wide angles lenses) ~ 25mA
3. OCR digits recognition algorithm -> writing result to flash mem
4. mosfet power control of Camera for standby mode
5. usb/serial or other interface to transmit results
6. 1..5 buttons/ jumpers/leds
Approximate work and budget:
…
Milestone A) Virtual simulation of the electrical circuit + complete code writing + modular prototyping ~2500 $
Milestone B) PCB ~ 1000$
the home laboratory has all the necessary equipment (including various versions of MCUs and discovery boards), except cameras with the required specific optics of short focus, so additional budget for fast delivery of camera modules is required.
-
1 dzień16 PLN
160 1 dzień16 PLN
We can complete this project using a neural network to recognize numbers on board STM MCU. e.g. Tensor flow. We will determine the cost and term after receiving the technical specifications.
-
25 dni6168 PLN
2827 36 0 1 25 dni6168 PLN
I became interested in your project. Ready for cooperation. I see the implementation of the project on low-power STM processors using opencv libraries
-
7 dni2056 PLN
1036 44 0 7 dni2056 PLN
Buongiorno!
Per favore, fornisca tutti i dettagli necessari.
Sarò lieto di fare il vostro ordine!
Aktualne zlecenia dla freelancerów w kategorii Systemy wbudowane i mikrokontrolery
Przeprogramowanie automatycznej prasy przemysłowej
411 PLN
Opisuję zasadę działania, a także zmiany, które należy wprowadzić Proszę o propozycje cenowe Zasada działania urządzeniaUrządzenie składa się z trzech głównych węzłów, które działają synchronicznie:silnik krokowy podawania (podajnik);stempel do wycinania otworów;gilotyna do… Systemy wbudowane i mikrokontrolery, Doradztwo inżynieryjne ∙ 4 dni 12 godzin temu ∙ 4 oferty |
Pisanie kodu dla ArduinoPotrzebne jest opracowanie oprogramowania dla wagowego dozownika opartego na Arduino Uno. Komponenty: Arduino Uno R3 HX711 + czujnik tensometryczny Wyświetlacz LCD1602 I2C Matryca LED MAX7219 8x32 5 przycisków sterujących 4-kanałowe przekaźniki 2 lampy sygnalizacyjne Wibromagnes… C i C++, Systemy wbudowane i mikrokontrolery ∙ 11 dni 11 godzin temu ∙ 15 ofert |
romskie