Switch to English version?

Yes

Переключитись на українську версію?

Так

Переключиться на русскую версию?

Да

Przełączyć się na polską wersję?

Tak

Login
Registration
- Welcome to Freelancehunt
  
  Work risk-free, saving time and money
  
  Login Registration

Post your project for free and start receiving proposals from freelancers within minutes after publication!

29 USD

3D model for printing

29 USD

3D Modeling

6 out of 6

project complete

publication
open for proposals
terms confirmation
reservation
work underway
project complete

Project translated automatically. Log in or register, to view the original

There is an existing guitar model (in the inside of the silk). You need to thick the “corpus” (black, green, violet red). The black color must be broken parts. Green in the pressure. The gradient of the red violet must be essentially a change of height from the higher to the lower.

I call it. A part of the model (sire middle on the sketch) already exists! It is not necessary to guess the sizes but to raise them proportionally to the sketch! The thickness of the corner model to throw should be +\- such thickness (including the breakthrough). Conditionally: if we have a thickness of the grey part of 5cm then the wings of the metal should be 5cm. There is a red color, there is a green color, there is a red color, there is a red color, there is a red color, there is a red color, there is a red color, there is a red color, there is a red color, there is a red color, there is a red color, there is a red color, there is a red color. There are no clear requirements to the height. They need to be done by themselves to clearly differentiate the areas that will then be welded. But the overall thickness should not be greater than the thickness of the existing detail.
The model will also need to be cut with the keys on the 44cm workplace.

Наголошую. Частина моделі (сіра середина на ескізі) вже існує! Тобто непотрібно вигадувати розмірів а лиш підігнати їх пропорційно до ескізу! Товщина моделі котру потрібно дробити повинна бути +\- такої товщини (враховуючи перепад). Умовно : якщо ми маємо товщину сірої частини 5см то і крила метелика повинні бкти 5 см. там де чорий колір, 3-4 см там де зелений колір і 2-3 там де фіолетово-червона зона. Знову ж таки нема чітких вимог до висоти. ЇЇ потрібно зробити самому щоб чітко відрізнити зони які потім будуть поварбовані. але загальна товщина повинна бути не більше товщини існуючої деталі.

Модель також потрібно буде порізати з ключами на робоче поле 44см.

Client's review of cooperation with Maksim K.

Quality

Professionalism

Cost

Contactability

Deadlines

A good robot. I recommend.

Dmytro Basiuk | Safe

Freelancer's review of cooperation with Dmytro Basiuk

Payment

Task setting

Clarity of requirements

Contactability

Good luck, I recommend it!
The work is good, the work is good.

Maksim K. | Safe

Proposals 4
Withdrawn 1

by default date online rating cost completion time

45 USD

Vadim R.

37 2

45 USD

Ready for smooth cooperation. Interesting and creative task, and that is inspiring) I have my own 3D printer, so I know and consider technical nuances. Look at the portfolio in the profile:
Freelancehunt
Let me write!

Show original

Translate

14 October 2023, 9:21

28 USD

Sergey Slipchuk

19 1

28 USD

Good day .
It was a strange task, but nothing was done.

What are the dimensions of the silk, as well as the inchi dimensions of the "corpus"?
What should the height be?
How big is it?

Ready to discuss your project and implement it.

… to turn.

With respect,
by Sergey

Show original

Translate

14 October 2023, 4:21

Another 2 proposals concealed

1 proposal concealed

Current freelance projects in the category 3D Modeling

Label project + 3D visualization (Supplement for men / NUTRA) Hello. I am looking for an experienced designer for ongoing or one-time collaboration on a dietary supplement brand in the NUTRA category.Scope of work: Designing a label for the packaging (supplement dedicated to men – modern, masculine, premium design). Preparing a… Packaging and label design, 3D Modeling ∙ 2 hours 25 minutes back ∙ 18 proposals
Creation of a BIM model in REVIT Creation of a BIM model in REVIT with specified technical characteristics of the product, including appearance and dimensions of the product. 3D Modeling ∙ 5 hours 4 minutes back ∙ 1 proposal
3D modeling and equipment layout for an adaptive fitness studio (246 sq. m) I am looking for a 3D designer/architect to develop a volumetric layout plan for the placement of equipment and zoning of a fitness studio focused on adaptive rehabilitation. The premises are located on the 1st floor of a new building in Kyiv. The total area is 246 sq. m. Main… 3D Modeling ∙ 6 hours 31 minutes back ∙ 10 proposals
PROJECT OF LANDSCAPING PANDA BEAR STUDIO WELLNESS GARDEN PROJECT OF LANDSCAPING PANDA BEAR STUDIO WELLNESS GARDEN Location: Reading, United Kingdom. About the project: It is necessary to develop a concept and visualization of an outdoor wellness space at the Panda Bear Studio yoga and pilates studio. Style: modern wellness retreat… 3D Modeling ∙ 7 hours 23 minutes back ∙ 9 proposals
Looking for a CAD designer (remote, project work) 1000 USD We are looking for a specialist to work with 3D models in CAD programs.Requirements: • Basic knowledge of Meshmixer, CADflow, Fusion 360, or similar programs. • Attention to detail. • Ability to work according to technical specifications. • Responsibility and adherence to… 3D Modeling ∙ 16 hours 59 minutes back ∙ 2 proposals	1000 USD

Dmytro Basiuk

Ternopol 25

3D model for printing

Client's review of cooperation with Maksim K.

Freelancer's review of cooperation with Dmytro Basiuk

Current freelance projects in the category 3D Modeling

Label project + 3D visualization (Supplement for men / NUTRA)

Creation of a BIM model in REVIT

3D modeling and equipment layout for an adaptive fitness studio (246 sq. m)

PROJECT OF LANDSCAPING PANDA BEAR STUDIO WELLNESS GARDEN

Looking for a CAD designer (remote, project work)