Switch to English?
Yes
Переключитись на українську?
Так
Переключиться на русскую?
Да
Przełączyć się na polską?
Tak
Post your project for free and start receiving proposals from freelancers within minutes after publication!

Design of Printed Plate

Translated

  1. 653    2  1
    5 days107 USD

    It looks typical. I can do in altium, some of the components are already there. If it could be good to see more in detail what final task and more detailed TZ

  2. Another 2 proposals concealed
  • Profile blocked
    26 September 2023, 4:52 |

    Сенсорная кнопка зачем? Точнее как єто должно работать?


    В целом есть дизайн или ТЗ? 

    Какие ограничения по устройсву? (Размер, тепло, потребление, влага и тд)

  • Vitaly Revenchuk
    26 September 2023, 5:03 |

    Ограничений нет, сенсорная кнопка подаст сигнал на выход, я должен получить его на любом gpio ESP, дизайна тоже нет, есть лишь идея.

    Меня устроит любое исполнение, это просто должно работать 😁

  • Profile blocked
    26 September 2023, 5:41 |

    А почему тогда не простая кнопка?

    Чем не подошли готовые сборки от ttgo?

  • Vitaly Revenchuk
    26 September 2023, 9:15 |

    Сенсорная будет работать через тонкий пластмассовый корпус.

    ttgo подходит, вы абсолютно правы, но не хочется использовать полностью готовый модуль

  • Profile blocked
    26 September 2023, 15:18 |

    И очень зря не хотите готовый использовать

    Как я понимаю у вас пока на стадии "сам не знаю что в итоге" а значит готовое устройсво в приоритете


    А вот когда в поле уже все тонкости утрясутся и станет понятно что нужно, какой формы и тд, вот тогда можно думать за плату (плата в первыю очередь делается ради форм-фактора и удешевления)


    А за кнопку используйте обычные и не переживайте. Для зашиты от воды силиконовая мембрана, которую можно прямо на корпусе отлить дома монолитно.

    С сенсорными много подводных, из основного - важно что бы статика с корпуса снималась и грязь или влага уже будет неадекватно обрабатыватся

Current freelance projects in the category Embedded Systems & Microcontrollers

Schematic and PCB design

89 USD

It is a simple fan controller schematic. I will provide a hand-drawn sketch of the schematic. You need to create the schematic in KiCad and implement the PCB design. Add the implementation of a small Buck converter to the schematic. Details will be discussed further along the…

Embedded Systems & MicrocontrollersDrawings & Diagrams ∙ 11 hours 47 minutes back ∙ 3 proposals

Telegram

164 USD

I am offering a job to restore access to a Telegram account. My Telegram account has been hacked, so I am looking for a specialist who can help solve this problem and restore access to the account. I am open to considering your proposals regarding the cost of services.…

Embedded Systems & MicrocontrollersApps for iOS (iPhone and iPad) ∙ 17 hours 25 minutes back ∙ 6 proposals

STM32H743 + Ethernet (OpenH743I-C DevBoard)

For the DevBoard OpenH743I-C (https://arduino.ua/prod6139-plata-rozrobnika-openh743i-c-standard-stm32h7-development-board ) and the ETHERNET module based on the DP83848 chip, generate firmware to test the operation of the Ethernet module at the hardware level. Examples of the…

Embedded Systems & Microcontrollers ∙ 8 days 7 hours back ∙ 5 proposals

Development of a GPS-GSM tracker

112 USD

Hello! A GPS-GSM tracker needs to be developed. The device should be small in size. The operating range is 6-32V. It should have a built-in battery that allows it to operate for 3-4 hours without external power. The main task is location tracking. The device should have: - a…

Embedded Systems & MicrocontrollersEngineering ∙ 9 days 13 hours back ∙ 2 proposals

Need to exit Android watch from cyclical fastboot.

The Mobvoi Ticwatch 3 pro GPS watch entered a cyclic fastboot mode during a firmware flashing attempt. I am looking for someone who can fix it and determine if it is possible to install the firmware.

Embedded Systems & Microcontrollers ∙ 9 days 13 hours back ∙ 2 proposals

Client
Vitaly Revenchuk
Ukraine Kyiv  1  0
Project published
2 years back
103 views