Viewing the scheme in Proteus 8
11 USD 1) Placing on the ATmega88PA scheme at a frequency of 16 MHz
2) To the SPI pipe to connect the shift register 74HC595
3) On the 1.3.57.7 ports of the register to connect N channel Mosfet transistors with the control voltage of 3-5 volt (find any with the logical level in the base of data to the current up to 2A), to connect through the corresponding resistors, the opening time is not more than 0.01s:-) .4) In the transistors to connect the inductive loads H = 5mH R = 6 Ohm,
5) Inductive load to connect to a separate DC source of 12V and internal resistance of 0.1 Om.6) Parallel to the inductive load in the transistor stain set the protective discharge diode, add the protective (ESD) stabilitons between the lock and the output by 6-7 volt.7) On the remaining clear ports 0.2.4.6 the register hangs by LED.8) Write a simple program(ASM or C) that in an infinite cycle performs:Give a 1 second width impulse on a LED 0Give a 0.1 second width impulse on a Transistor 1Give a 1 second width impulse on a LED 2Give a 0.1 second width impulse on a Transistor 3and so on
9) Add the oxygen.and show U,I through the shells, as well as U,I on the gasing diode.10) Delete the work project.
Work results
Client's review of cooperation with Oleg Redkach
Viewing the scheme in Proteus 8I liked the work of the freelancer, the task was done quickly and well.
It is understood in AVR MK.
I recommend it.
Freelancer's review of cooperation with Aleksandr L.
Viewing the scheme in Proteus 8Everything is great! I recommend cooperation.
-
Winning proposal3 days11 USD
46 1 0 Winning proposal3 days11 USD
Hello to you! Ready to perform, there is a decent experience of working with Proteus various versions and its analogues, programming, schema engineering.
Current freelance projects in the category Embedded Systems & Microcontrollers
STM32H743 + Ethernet (OpenH743I-C DevBoard)
For the DevBoard OpenH743I-C (https://arduino.ua/prod6139-plata-rozrobnika-openh743i-c-standard-stm32h7-development-board ) and the ETHERNET module based on the DP83848 chip, generate firmware to test the operation of the Ethernet module at the hardware level. Examples of the… Embedded Systems & Microcontrollers ∙ 2 days 7 hours back ∙ 5 proposals |
Development of a GPS-GSM tracker
111 USD
Hello! A GPS-GSM tracker needs to be developed. The device should be small in size. The operating range is 6-32V. It should have a built-in battery that allows it to operate for 3-4 hours without external power. The main task is location tracking. The device should have: - a… Embedded Systems & Microcontrollers, Engineering ∙ 3 days 13 hours back ∙ 2 proposals |
Need to exit Android watch from cyclical fastboot.The Mobvoi Ticwatch 3 pro GPS watch entered a cyclic fastboot mode during a firmware flashing attempt. I am looking for someone who can fix it and determine if it is possible to install the firmware. Embedded Systems & Microcontrollers ∙ 3 days 13 hours back ∙ 2 proposals |
Tuya smart projectFor a Wi-Fi device. Looking for a specialist with Tuya IoT Platform / Tuya Panel Studio experience, working with CBU is a must! Tasks to be completed: Account registration 1. Product configuration in Tuya IoT Platform 2. Configuration of Data Points (DP) 3. Interface development… Embedded Systems & Microcontrollers, Hybrid Mobile Apps ∙ 4 days 9 hours back ∙ 4 proposals |
Software development for Arduino (RF modules 3–7.5 GHz, automatic frequency scanning)It is necessary to develop a system on Arduino for the automatic search of active analog video signals and the automatic tuning of the transmitter to the detected frequency.It is planned to use three separate transceiver modules: 3000–4200 MHz; 4900–6000 MHz; 6100–7500… C & C++, Embedded Systems & Microcontrollers ∙ 5 days 20 hours back ∙ 4 proposals |
Kyiv