Budget: 6000 UAH Deadline: 10 days
Good day, I am currently working on an Arduino project and would also take your project ready for collaboration. Write to me on Telegram indicated in my profile.
An interesting project for enthusiasts of unconventional solutions. What is the essence:
There is a car that has a non-standard transfer case with differential lock and low gear modes. Currently, all of this is controlled by two remotes:
— one from the winch, which rotates the motor-reducer clockwise and counterclockwise, thereby engaging different modes;
— the second remote — with a relay and two buttons that control the transfer case brake.
The problem is that if you simply turn the transfer case reducer to the stop, only the low gear mode without locking is activated. To engage the differential lock, it is necessary to turn it to the stop and additionally activate the so-called transfer case brake (with the second remote).
What is the idea and task?
I am tired of using these remotes and constantly guessing whether the required mode has been activated. I want to implement control in the following way:
— an analog button at 12 V:
the first button rotates the reducer to the stop counterclockwise, engages the brake, and disconnects the rotation power
(differential lock mode);
— the second button rotates the reducer to the stop clockwise, also engages the brake, and disconnects the rotation power
(differential lock mode + low gear).
“Fool-proof” protection is not important. The functionality is what matters.
Ideally — implement all control through an application on Android (that is, from a phone).
I can easily provide the reducer and its pinout.
The motor number with the reducer: 95562460100
Propose a budget.
Budget: 6000 UAH Deadline: 10 days
Good day, I am currently working on an Arduino project and would also take your project ready for collaboration. Write to me on Telegram indicated in my profile.
Budget: 12000 UAH Deadline: 7 days
Hello. Quite an interesting and complex project.
I can immediately see where we can reduce the execution time and budget - instead of an Android application, we can create a web interface on ESP (we connect to the board via WiFi and can fully control the device).
Additionally, I have skills in 3D modeling and printing (buttons, cases, etc.).
I am also located in Kyiv.
Budget: 15000 UAH Deadline: 10 days
I suggest dividing the idea into two subtasks:
1. Arduino
2. Mobile application
Creating the mobile application is not difficult.
Please let me know the details of which part is done on Arduino, after that we can discuss implementation and budget.
Budget: 7000 UAH Deadline: 7 days
Good day, I am interested in the project. Could you please specify which part you are offering to complete? Do you need an application, and the work with Arduino on your side, or do you need a turnkey project?
Budget: 27000 UAH Deadline: 4 days
Good day! I am ready to complete this project. Extensive experience in developing various applications.
The goal of the project is to create two devices that will communicate with each other via cable (485). 1) The first device is a metal casing with connectors, it is a switching block with 16 relays + Ebyte-400M2213S which will check for the presence of a signal at specified frequencies. 2) This is a control panel on esp32 mcu2.8 smart display. Its purpose is to control the load and receive data from the switching block about the presence of a signal at specified frequencies. A specialist or specialists are needed who have experience in such work. Circuit design and programming. All technical resources will be provided. We discuss the project, possible changes, etc... and we work.
Development of a Flight Controller for Fixed-Wing UAVs An experienced Embedded Hardware Engineer is needed to develop a flight controller for fixed-wing UAVs. Tasks: develop the electrical schematic; design a multilayer PCB; select the component base; prepare Gerber, BOM, and Pick&Place for mass production. Main requirements: microcontroller STM32H743 or equivalent class; functionality similar to Matek H743-Wing V3 (without copying); compatibility with PX4 or ArduPilot; interfaces: CAN, UART, SPI, I2C, USB, PWM; support for connecting GPS, IMU, barometer, telemetry, and other peripherals; maximum use of components that meet NDAA requirements (without using Chinese components where possible). Mandatory when responding: describe your experience in developing Flight Controllers or other Embedded platforms; provide examples of completed projects; indicate which CAD systems you use (Altium, KiCad, etc.); specify estimated timelines and costs for completion. Preference will be given to contractors with experience in developing electronics for UAVs, robotics, or avionics.
There is a board with esp32, sim800l, mini 560pro 5v. It has two pulse inputs (coin, bill). 1. A 6-pin connector (mdb) needs to be made. 2. Integrate power into the board, it can be replaced with ti, Pololu D24V5F3 6-30V 3.3V / 1.5A, as a choice or integrate the existing module into the board. 3. Replace sim 800l with another module (the pins fit, but differ in places). Gerber files are available, there are no schematics, base jlpcb.
I have some logic in Google Excel related to the integration with the Nova Poshta API and the Turbosms API. Overall, everything works fine, but some functionality needs to be added. All details will be discussed in correspondence. I will provide access to the Excel and the code. It is essential for the performer to have experience working with Google Excel JS in Apps Script.