Organizer for a restaurant
Create an organizer for a restaurant based on the required parameters. For sauces, toothpicks, napkins, spoons, and forks. Compactness is the most important condition.
Technical assignment for a 3D modeler: Desktop organizer
**Goal:** Develop the geometry of a multi-level desktop organizer based on the shape, layout, and functional zones from references. The final model must be ready for 3D printing.
**Style and Material:** Monolithic, streamlined, biomorphic design. Surface - clean matte plastic (simulating PETG), without any graphics, text, logos, or QR codes.
**Layout and Functionality:**
Accurately reproduce all compartments and their mutual arrangement:
1. **Back compartment:** Deep, wide, for napkins.
2. **Front-Left:** Well for toothpicks.
3. **Front-Center:** Two wells for bottles (like Tabasco and with a cork).
4. **Right side (Two-level):** A single compartment with an internal partition creating two levels.
* *Upper level:* Four oyster forks.
* *Lower level:* Four coffee spoons.
Model Requirements:
Clean mesh without errors.
All surfaces smooth and clean.
Техническое задание для 3D-моделиста: Настольный органайзер
**Цель:** Разработать геометрию многоуровневого настольного органайзера на основе формы, компоновки и функциональных зон из референсов.Итоговая модель должна быть готова к 3D-печати.
**Стиль и Материал:** Монолитный, обтекаемый, биоморфный дизайн. Поверхность — чистый матовый пластик (имитация PETG), без какой-либо графики, текста, логотипов или QR-кодов.
**Компоновка и Функционал:**
Воспроизвести точно все отсеки и их взаимное расположение:
1. **Задний отсек:** Глубокий, широкий, для салфеток.
2. **Фронт-Лево:** Колодец для зубочисток.
3. **Фронт-Центр:** Два колодца для бутылочек (типа Табаско и с пробкой).
4. **Правый бок (Двухуровневый):** Единый отсек с внутренней перегородкой, создающей два уровня.
* *Верхний уровень:* Четыре устричные вилки.
* *Нижний уровень:* Четыре кофейные ложки.
Требования к Модели:
Чистый меш без ошибок.
Все поверхности гладкие и чистые.
Here is an ultra-compact technical specification in Russian, fully ready for production or designers:
## TECHNICAL ASSIGNMENT: DESKTOP ORGANIZER (V2.1)
**Dimensions and branding:**
* **Base:** 200 mm (Width) × 130 mm (Depth).
* **Max. height:** 200 mm (Overall dimension at the highest point of the back wall).
* **Text area:** The back wall protrudes above the body, forming an open edge for engraving/printing the logo or table number.
**Compartment specifications:**
* **For napkins (at the back):** 110 mm × 50 mm. For napkins 100 mm (W) × 150 mm (H), installed vertically on a narrow edge. At the front — a V-shaped cutout for easy grip.
* **For utensils (on the side):** Two compartments about 5 cm (50 mm) wide for forks and spoons (for utensil heights up to 100 mm).
* *Feature:* **The bottom is sloped**, so utensils slide into one corner and stand neatly together.
* **For sauces (at the front):** Two wells with a diameter of 40 mm. For bottles up to 130 mm in height.
* **For toothpicks (at the front):** One well with a diameter of 30 mm with a lowered edge.
**Structural requirements:**
* **Sturdy base:** The thickness of the bottom of the organizer must be **about 1 cm (10 mm)** for maximum strength and stability against tipping over.
* **Drainage system:** In all compartments (for napkins, utensils, and sauces) **drainage holes must be provided** for water drainage and easy washing. **In the compartment for toothpicks, making a drainage hole is PROHIBITED**.
* **Design:** Streamlined monolithic shape with rounded corners to prevent chipping (according to the concept image.png). Cascading height (from back to front) for easy access.
Вот ультракомпактное ТЗ на русском языке, полностью готовое для отправки на производство или конструкторам:
## ТЕХНИЧЕСКОЕ ЗАДАНИЕ: НАСТОЛЬНЫЙ ОРГАНАЙЗЕР (V2.1)
**Габариты и брендирование:**
* **Основание:** 200 мм (Ширина) × 130 мм (Глубина).
* **Макс. высота:** 200 мм (Полный габарит по верхней точке задней стенки).
* **Зона текста:** Задняя стенка выступает над корпусом, формируя открытый бортик для гравировки/печати логотипа или номера стола.
**Спецификация отсеков:**
* **Для салфеток (сзади):** 110 мм × 50 мм. Под салфетки 100 мм (Ш) × 150 мм (В), установка вертикально на узкое ребро. Спереди — V-образный вырез для удобного хвата.
* **Для приборов (сбоку):** Два отсека шириной около 5cm (50 мм) для вилок и ложек (под высоту приборов до 100 мм).
* *Особенность:* **Дно выполнено под наклоном**, чтобы приборы соскальзывали в один угол и аккуратно стояли вместе.
* **Для соусов (спереди):** Два колодца диаметром 40 мм. Под флаконы высотой до 130 мм.
* **Для зубочисток (спереди):** Один колодец диаметром 30 мм с заниженным бортиком.
**Конструктивные требования:**
* **Прочное основание:** Толщина дна органайзера обязательно должна составлять **около 1 см (10 мм)** для максимальной прочности и устойчивости к переворачиванию.
* **Дренажная система:** Во всех отсеках (для салфеток, приборов и соусов) **необходимо предусмотреть дренажные отверстия** для стока воды и легкой промывки. **В отсеке для зубочисток дренажное отверстие делать ЗАПРЕЩЕНО**.
* **Дизайн:** Обтекаемая монолитная форма со скругленными углами для защиты от сколов (согласно концепции image.png). Каскадная высота (сзади наперед) для удобного доступа.
Applications 3
Client's review of cooperation with Danilo Hablak
Organizer for a restaurantUnfortunately, we did not agree on the quality of the result.
-
2 days30 USD
364 1 0 2 days30 USDGood day, I am ready to complete the order. Examples of my print work
Google Drive
-
2 days25 USD
646 6 0 2 days25 USDI specialize in development and modeling for 3D printing. Message me privately, and we will discuss.
-
1 day25 USD
319 2 0 1 day25 USDReady to complete the model, deadline 1 day. Write to me, we will discuss the details in private messages.
-
1 day25 USD
139 15 0 1 1 day25 USDGood day! I am interested in completing your project, I will do it based on the sample photo and your dimensions. Feel free to reach out.
-
2 days30 USD
2896 53 0 2 days30 USDHello
almost ready, feel free to contact me and I will show you
Portfolio hereBehance
-
1 day30 USD
1395 11 0 1 day30 USDHello! Feel free to contact me, I will do it quickly and with high quality. As close as possible to your reference. I work in SolidWorks. I will provide the file in the required format.
-
1 day30 USD
463 1 day30 USDGood day, I will do your work quickly and efficiently, I have experience in making various organizers. Please send a private message, and we will discuss the details.
-
1 day30 USD
1147 14 0 1 day30 USDGood day! I am ready to complete the project. Please write to discuss the details.
-
Winning proposal1 day25 USD
2344 16 2 1 Winning proposal1 day25 USDGood day, I am very interested in working with you. I offer quality execution of the tasks set and promptness. Let's discuss the details in a private chat and start our collaboration.
-
2 days55 USD2 days55 USD
I will model such an organizer, as in the example, according to your requirements. The price is indicated taking into account the service fee. Write to me.
-
2 days40 USD
3503 17 1 2 days40 USDGood day! I am ready to help you bring your project to life! Quite an interesting task. I have over 20 years of experience, and I guarantee quality. I would be happy to collaborate!
-
2 days100 USD
139 2 days100 USDGood day, I work with 3D printing development. I am ready to collaborate.
-
3 days50 USD
3842 47 2 3 days50 USDGood afternoon
I am ready to participate in an interesting project
Discussion in the project workspace
-
так он же у вас на столі (я так розумію це готовий). що конкретно з ним треба зробити?
-
якийсь бідненький у вас ресторан, раз повідхиляли всіх, хто більш-менш адекватну ціну вище за $30 ($27.30 на руки) поставив 🤔
-