PCB development of video scanner board
Development of a PCB board for printing is needed. This is a video signal scanner
Main parameters of the board:
- Size: 160x100mm
- 2 layers, thickness 1.6mm
- Copper: 1oz (35μm)
- Minimum trace width: 0.2mm
- Minimum gap: 0.2mm
- Components by sections:
RF Section:
MM238R (5.8GHz):
- Power supply: 3.3V, decoupling 100nF + 10µF
- RSSI output: divider 10kΩ + 100nF
- RF input: SMA connector, 50Ω
SM1370R/1 (1.2GHz):
- Power supply: 5V, decoupling 100nF + 10µF
- RSSI output: divider 10kΩ + 100nF
- RF input: SMA connector, 50Ω
Video switching:
- MAX4583
- Video matching: 75Ω resistors
- Decoupling: 100nF at input/output
- Control: 1 digital pin
Control (ATmega328P):
- TQFP-32 package
- Crystal 16MHz + 2x22pF
- Reset: 10kΩ pull-up
- Power supply: 100nF + 10µF
- ICSP connector: 2x3 pins
OLED display:
- 0.96" SSD1306
- I2C connection:
* SCL: pull-up 4.7kΩ
* SDA: pull-up 4.7kΩ
- Power supply 3.3V + 100nF
Power supply:
Input (battery):
- JST-XH connector
- Reverse polarity protection
- Filter: 100µF electrolytic
5V converter (MT3608):
- Input: 22µF ceramic
- Output: 47µF ceramic
- Inductor: 22µH/2A
- FB: 10kΩ + adjustment
3.3V regulator (AMS1117):
- Input: 10µF
- Output: 22µF
- Layer routing:
Top layer:
- RF traces
- Components
- Signal lines
- Power supplyBottom layer:
Solid ground
- Power polygons
- Return signals- Critical areas and rules:
RF area:
- Via-wall around RF modules
- Minimum components
- Shielding from the digital part
Video signals:
- Shielding from RF
- Minimum crossings
- 75Ω matching
Power supply:
- Power traces 0.8mm+
- Star topology
- Decoupling near consumers- Test points:
- RSSI of both receivers
- Video input/output
- 3.3V, 5V
- I2C lines
- Mechanical requirements:
- Mounting holes: 4x M3
- RF screen mounting
- Space for heatsinks
File generation:
- Gerber RS-274X
- Excellon for drilling
- BOM (bill of materials)
- Assembly drawing
-
1488 37 0 Good day. I am ready to complete your project. I work in Altium Designer. Write to me, we will discuss the details.
-
Доброго дня.
Замовлення має назву: "PCB розробка платки відео сканера". Але дивлюся на опис, то чомусь здається враження що не тільки РСВ плата потрібна, але ще й схема самого сканеру.
Я нічого не переплутав? Електрична схема є у наявності?
Якщо маєте схему, то далі можлива співпраця.
-
Сделайте мне детектор дронов на 1.2 и 2.5 ГГц за три тысячи гривен. А почему не за пиво?
-
Current freelance projects in the category Drawings & Diagrams
Develop metal structures for roofs on entrance groups
67 USD
It is necessary to develop metal frames for roofs over entrance groups (entrance group 1 - roof over the gate, entrance group 2 - roof over the gate with a door), specifically: supports for the roof metal structure, the metal structure of the roof itself, materials, fastening… Drawings & Diagrams ∙ 4 hours 55 minutes back ∙ 4 proposals |
Sheet metal cabinet 0.8 mm
22 USD
Design of a Metal Locker CabinetGeneral Information It is necessary to develop a complete set of drawings and a 3D model of the locker cabinet for further production from sheet metal.Dimensions of the Product Height — 2100 mm. Width — 600 mm. Depth — 485 mm.Construction Two… Engineering, Drawings & Diagrams ∙ 6 hours 49 minutes back ∙ 5 proposals |
Create a layout for a detailed paper architectural model based on the sketch project.I'm looking for a specialist who can prepare a high-quality and very detailed layout for creating a physical model from paper/cardboard. There are source materials for the project: — facades; — sections; — visualizations; — sketch architectural project; — file in .pln format; —… Drawings & Diagrams ∙ 1 day back ∙ 2 proposals |
Point cloud to Revit (A3852)For a future architectural project, it is necessary to model a building and the land with roads and stairs from a point cloud. Develop a 2D drawing with the main dimensions, total and living areas of the premises. Output data can be found at the link:… Architectural Design, Drawings & Diagrams ∙ 1 day 4 hours back ∙ 3 proposals |
Point cloud to Revit (A3738)For the future architectural project, it is necessary to model the building and the land with roads and stairs using a cloud of points. The roof of the adjacent building also needs to be modeled. Develop 2D drawings with the main dimensions, total and living areas of the… Architectural Design, Drawings & Diagrams ∙ 1 day 4 hours back ∙ 1 proposal |