Budget: 999 UAH Deadline: 1 day
Write, we'll figure it out and fix everything. And most importantly - quickly and efficiently ;)
I assembled a board based on Arduino, added a relay, and when trying to start it - there may have been a short circuit.
I need support, and if you are good at electronics - then I might offer you a few additional tasks - to improve this and several new boards.
Budget: 999 UAH Deadline: 1 day
Write, we'll figure it out and fix everything. And most importantly - quickly and efficiently ;)
Budget: 1000 UAH Deadline: 1 day
Hello,
please contact us regarding all the issues mentioned in the discussion,
the price is a conditional rate for 1 day
Budget: 1000 UAH Deadline: 15 days
About the diode, you have already been informed. If you need another collaboration, please reach out.
Budget: 1000 UAH Deadline: 1 day
Good day! I am ready to help with finding the error in the RCV. I can carefully check the scheme/code and find the malfunction.
Полярность диодов (на реле) не правильная. Надо катодом на питание, анодом на коллектор транзистора. Для поиска неисправностей для начала лучше их убрать
В группе по ардуино мне уже подсказали что неверно диод стоит)
Я оторвал на второй плате и реле начало работать, как сделаю все тесты остальной части - то уже попробую как-то припаять его правильной стороной)
Первая уже походу с пробитыми транзисторами - так как на базе 9вольт, а на ногу ардуино приходит 5.7в (хотя по факту должно быть 0)
У меня ещё впереди пару модулей(для умного дома), плюс попой чувствую что защита по питанию у меня очень слабая(что может выгореть пол платы, если что-то не так)
Если есть желание, могу поделится доступом к моему easyEda - растолковать какой функционал я в целом хочу сделать и оценишь по денежке сколько это будет мне стоить)
У меня готовы пока только 2 (модуль в подрозетник/выключатели, и вот этот вот реле модуль)
Впереди ещё диммирование Led лентами(мосфеты), диммирование led светильниками типа 220вольт, вентиляция, электро-штора и на другом чипе (esp32) для адресной led ленты(у atmega мало памяти и скорость скорее всего сильно хуже)
В помилку Вам вже вказали це діоди , транзисторам мабуть стало погано , від такого ))
Також зверніть увагу на даташит , для AMS1117 по виходу бажано встановлювати
електролит або тантал на 22 мкф , для більш стабільною праці
На вашу думку, чи вымагаэ така плата доопрацювання щодо захисту електроживлення ?
Я боюся як би одна помилка, не спалила всю електронiку за один раз))
Є багато схем, но сама простіша для Вас як початківця , поставьте діодний міст ( та електроліт після нього ) по входу і вас вже не буде лякати що ви щось не так підключили.)
Та зможете напряму використовувати трансформатор) для ваших експериментів.
Також рекомендую робити все же на stm32:, та не витрачати час на avr.
Если размер маленький, можно открыть в новой вкладке - он будет в полный размер
Development of a Flight Controller for Fixed-Wing UAVs An experienced Embedded Hardware Engineer is needed to develop a flight controller for fixed-wing UAVs. Tasks: develop the electrical schematic; design a multilayer PCB; select the component base; prepare Gerber, BOM, and Pick&Place for mass production. Main requirements: microcontroller STM32H743 or equivalent class; functionality similar to Matek H743-Wing V3 (without copying); compatibility with PX4 or ArduPilot; interfaces: CAN, UART, SPI, I2C, USB, PWM; support for connecting GPS, IMU, barometer, telemetry, and other peripherals; maximum use of components that meet NDAA requirements (without using Chinese components where possible). Mandatory when responding: describe your experience in developing Flight Controllers or other Embedded platforms; provide examples of completed projects; indicate which CAD systems you use (Altium, KiCad, etc.); specify estimated timelines and costs for completion. Preference will be given to contractors with experience in developing electronics for UAVs, robotics, or avionics.
There is a board with esp32, sim800l, mini 560pro 5v. It has two pulse inputs (coin, bill). 1. A 6-pin connector (mdb) needs to be made. 2. Integrate power into the board, it can be replaced with ti, Pololu D24V5F3 6-30V 3.3V / 1.5A, as a choice or integrate the existing module into the board. 3. Replace sim 800l with another module (the pins fit, but differ in places). Gerber files are available, there are no schematics, base jlpcb.