Setting the OSB on the framework
22 USD 1) to develop a scheme of discharge on the floor.On the stairs of the plates must be the base (board), and the plates of the floor and steel must be in the chess order.Here is an approximate layout of the floor, as I designed it: https://tppr.me/v8Tbv - here are used the whole leaves of the osb, and there are lots - it's parts of the cut into several parts of one leaf.In fact, you need to make the 1 module layout and repeat it on others, because the floor area of the modules is the same and the frame is the same.From the nuances - the stick should be in the middle of the ball, and on the floor the leaf goes to the very edge of the frame: https://tppr.me/1Bb1v - the wall is placed on the osb.2) also develop the steel scheme.According to the idea, it should repeat the floor discharge.3) to develop a scheme of the OSB wall discharge.There is no chess order.All the leaves are mounted vertically equating down the frame.The height of the wall is 2700, the range is 2500, but the stretch occurs on the rigle, because above is a plate of 50mm + under it the rigle is vertically 200mm.The layout is approximately like this: https://tppr.me/qXHeq - down the whole list of osb, above a piece of 200mm.From the nuances - here I also designed so that the minimum of cuts was: https://tppr.me/aGqE2 - on the example of the frame of the wall with a window - height as on the dirty wall (2500+200), and on the width of the edge - 312 mm (this is a blade of 1250 mm width cut into 4 parts).The same example of the layout on the frame of the entrance wall https://tppr.me/jrRGX (only I showed the outside and should be from the middle.It’s not easy to show from the middle.
Current freelance projects in the category Drawings & Diagrams
Development of KMD based on the completed projectAccording to the completed project for the separation of floors, it is necessary to develop detailed drawings in KMD for manufacturing at the factory. The project is available in PDF and DWG. Object Design, Drawings & Diagrams ∙ 5 hours 39 minutes back ∙ 4 proposals |
Develop metal structures for roofs on entrance groups
67 USD
It is necessary to develop metal frames for roofs over entrance groups (entrance group 1 - roof over the gate, entrance group 2 - roof over the gate with a door), specifically: supports for the roof metal structure, the metal structure of the roof itself, materials, fastening… Drawings & Diagrams ∙ 23 hours 25 minutes back ∙ 6 proposals |
Sheet metal cabinet 0.8 mm
22 USD
Design of a Metal Locker CabinetGeneral Information It is necessary to develop a complete set of drawings and a 3D model of the locker cabinet for further production from sheet metal.Dimensions of the Product Height — 2100 mm. Width — 600 mm. Depth — 485 mm.Construction Two… Engineering, Drawings & Diagrams ∙ 1 day 1 hour back ∙ 10 proposals |
Create a layout for a detailed paper architectural model based on the sketch project.I'm looking for a specialist who can prepare a high-quality and very detailed layout for creating a physical model from paper/cardboard. There are source materials for the project: — facades; — sections; — visualizations; — sketch architectural project; — file in .pln format; —… Drawings & Diagrams ∙ 1 day 18 hours back ∙ 2 proposals |
Point cloud to Revit (A3852)
For a future architectural project, it is necessary to model a building and the land with roads and stairs from a point cloud. Develop a 2D drawing with the main dimensions, total and living areas of the premises. Output data can be found at the link:… Architectural Design, Drawings & Diagrams ∙ 1 day 23 hours back ∙ 3 proposals |
Kyiv