Development of PCB and 3D model of its case
134 USD Good afternoon.
It is necessary to develop a printed circuit board and a 3D model of a case in the 1 DIN form factor for it. The board and the list of all components must be ready for sending to manufacturing and assembly services, such as JLCPCB. The case model must be prepared for printing. After development, all files must be provided to the customer. The board is powered by 12 to 24 volts, and must have protection against sudden voltage drops and protection against incorrect polarity connection. On the back of the board, there should be a connector for power supply and interfaces. The board must include a header for connecting Raspberry Pi Pico W, SP3485, OLED display module SH1106, and a header for a 4-button membrane keyboard and its wiring. All unused pins (interfaces) from Raspberry Pi Pico W must be brought out to a separate header on the left side of the board (viewing the board from the front), and this header must also include 5-volt power, ground, and input stabilized voltage (12 or 24 volts). Near the Molex connector, pins that are not used in it should be brought out. That is, if an expansion board requiring pins for output (CAN, IBIS, etc.) is connected, this board can connect to them. The device will be operated in vehicles, so consider that it may be affected by increased temperature, vibration, and possible electromagnetic noise. More detailed information will be provided in correspondence. This board will be used for testing and will be installed in transport vehicles. Further cooperation in developing additional modules (expansion boards) and other components for this system is also possible.
Sincerely,
Ihor
Client's review of cooperation with Artem K.
Development of PCB and 3D model of its caseEverything was done professionally, with consultations during the course of the project. I recommend for collaboration
Freelancer's review of cooperation with Ihor Chyzhanskyy
Development of PCB and 3D model of its caseRealistic and detailed technical assignment, constructive, polite dialogue.
I recommend cooperation.
-
1 day22 USD
1832 12 1 1 day22 USD
Hello,
I work (from time to time) with JLPCB, their list of parts for PCBA is quite sparse
Regarding other points:
1. The board will be in Kicad, with gerbers/step/pos files at the output
2. The BOM will also include Digikey stock ID in parallel
3. Enclosure in FreeCAD
Price conditionally as a daily rate
-
9 days52 USD
1098 9 0 9 days52 USD
I can collaborate on this project together, I see no difficulties for myself
-
10 days52 USD
1531 40 0 10 days52 USD
I have extensive experience in developing enclosures for electronics for various manufacturing technologies and different fields of application regarding external influences.
Possible cooperation on mutually beneficial terms after discussion.
-
Winning proposal7 days134 USD
745 6 0 Winning proposal7 days134 USD
I have extensive experience in turnkey electronics development and will gladly help you implement this project!
-
"Розробка PCB та 3D моделі" - а схема електрична у Вас вже є?
-
Добрий день. Ні, лише опис підключення модулів до Pico
-
Current freelance projects in the category Embedded Systems & Microcontrollers
STM32H743 + Ethernet (OpenH743I-C DevBoard)
For the DevBoard OpenH743I-C (https://arduino.ua/prod6139-plata-rozrobnika-openh743i-c-standard-stm32h7-development-board ) and the ETHERNET module based on the DP83848 chip, generate firmware to test the operation of the Ethernet module at the hardware level. Examples of the… Embedded Systems & Microcontrollers ∙ 4 days 21 hours back ∙ 5 proposals |
Development of a GPS-GSM tracker
111 USD
Hello! A GPS-GSM tracker needs to be developed. The device should be small in size. The operating range is 6-32V. It should have a built-in battery that allows it to operate for 3-4 hours without external power. The main task is location tracking. The device should have: - a… Embedded Systems & Microcontrollers, Engineering ∙ 6 days 3 hours back ∙ 2 proposals |
Need to exit Android watch from cyclical fastboot.The Mobvoi Ticwatch 3 pro GPS watch entered a cyclic fastboot mode during a firmware flashing attempt. I am looking for someone who can fix it and determine if it is possible to install the firmware. Embedded Systems & Microcontrollers ∙ 6 days 3 hours back ∙ 2 proposals |
Tuya smart projectFor a Wi-Fi device. Looking for a specialist with Tuya IoT Platform / Tuya Panel Studio experience, working with CBU is a must! Tasks to be completed: Account registration 1. Product configuration in Tuya IoT Platform 2. Configuration of Data Points (DP) 3. Interface development… Embedded Systems & Microcontrollers, Hybrid Mobile Apps ∙ 6 days 23 hours back ∙ 4 proposals |
Software development for Arduino (RF modules 3–7.5 GHz, automatic frequency scanning)It is necessary to develop a system on Arduino for the automatic search of active analog video signals and the automatic tuning of the transmitter to the detected frequency.It is planned to use three separate transceiver modules: 3000–4200 MHz; 4900–6000 MHz; 6100–7500… C & C++, Embedded Systems & Microcontrollers ∙ 8 days 10 hours back ∙ 4 proposals |
Poltava