Доработать техническое задание(описать роли в действующем проекте)

I am looking for a performer for 3D modeling and the development of design documentation for a classic type air heating boiler fueled by wood, with a burning duration of 6-12 hours. Power output is 20 kW.Tasks: 3D model in SolidWorks (assembly + parts: casing, combustion chamber, heat exchanger, ash pan, flue gas unit) Working drawings of parts and assembly drawings Specification (BOM)Requirements: Experience in designing boilers, heat exchange equipment, or sheet metal (welded structures) Proficient in SolidWorks (Sheet Metal, Weldments) Understanding of basic thermal calculations — an advantageDeadline: 2 weeks Format: can be conveniently discussed after the responsePlease send a portfolio with examples of similar work (boilers, heat exchangers, welded metal structures).

Make technical cards for rolls, so that everyone can understand. 50-60 items. Cold, hot, and baked rolls

Development of a technical plan for sockets and switches based on the ready-made furniture drawing (Rivne / remotely). Hello! I am looking for a design engineer or technical draftsman to develop an electrical scheme for builders. What is available: An accurate drawing of the rooms with wall dimensions. Approved furniture and plumbing layout plan (where everything is placed). No 3D visualizations. What specifically needs to be done (Technical requirements): Socket and switch plan: Place points in relation to the dimensions of furniture and appliances. Specification by type (moisture protection): Clearly indicate the type of sockets for wet areas (for example, moisture-proof with grounding and IP44 covers for the bathroom). Calculation of power lines (cables): Highlight and specify power points that require a separate cable of increased cross-section (for example, for the cooktop, oven, powerful boiler) and separate lines for appliances like the extractor fan. Switch scheme: Consider convenient light control (three-way switches, linking to lighting groups). Result: A finished drawing in PDF format with accurate dimensions, clearances from walls/furniture, and technical notes for installers. Please indicate the cost of your work (for the entire project or per sq.m) and estimated completion time? 120 kV. Thank you!

Output data: Existing building: single-story office building; structural scheme — frame-less brick; external walls thickness 380–640 mm; internal load-bearing walls thickness 380–510 mm; ceilings — precast reinforced concrete hollow-core slabs; foundations — columnar with FBS blocks; approximate dimensions of the building — 40.34 × 28.84 m; building area — about 747 m². Planned: dismantling of the existing rafter system and roof; addition of a second floor with glued laminated timber structures; installation of a new wooden roof structure; reconstruction of the existing building with partial changes in loads on load-bearing structures.Required to perform: Analysis of the provided technical report on the building inspection. Verification calculation of existing foundations, walls, and ceilings for the perception of additional loads from the addition. Development of structural solutions regarding: installation of reinforced belts; strengthening of brick walls; strengthening of foundations (if necessary); ensuring spatial rigidity of the building; nodes for load transfer from glued laminated timber structures to the existing building. Calculation and justification of the adopted solutions. Issuance of a set of drawings for the stages of KB/CM/KZ (depending on the adopted solutions). Consulting support during the development of wooden structures and implementation of the project.Output documentation: Scientific and technical report on the building inspection. Measurement drawings. Architectural solutions for the addition. Preliminary concept of glued laminated timber structures.Requirements for the contractor: availability of a design engineer certificate in terms of ensuring mechanical resistance and stability; experience in the reconstruction of existing buildings; experience in designing the strengthening of brick or stone buildings; preferred experience working with additions of wooden structures or glued laminated timber.Message text for Freelancehunt Good day. We are looking for a designer to participate in the project of reconstructing an existing single-story brick office building with a subsequent addition of a second floor made of glued laminated timber. It is necessary to take on the development of structural solutions regarding: reinforced belts; strengthening of existing brick walls; if necessary — strengthening of foundations; ensuring spatial rigidity of the building; load transfer from new wooden structures to the existing building. A technical inspection of the building and measurement drawings have been completed, which will be provided to the contractor after preliminary discussion of the project. Preferred experience: reconstruction of existing buildings; development of solutions for strengthening stone or brick structures; work with additions or wooden structures. Please include in your response: a brief overview of your experience; examples of similar completed projects; available certificates; estimated budget and timelines for the work. We are ready for long-term cooperation on similar projects.