Budget: 500 UAH Deadline: 1 day
Готова помочь
Ищу специалиста по фотошопу. Надо сделать картинку на главную интернет-магазина с паралакс эффектом. Тоесть картинка в два слоя, и при накладании одна на другую получалась цельная. Как то так. Есть товар Конская мазь Editt cosmetics. Надо как то товар этот вставить, еще что то, написать кое что. Короче сам незнаю чего хочу, но должно быть красиво.
Что можете предложить и какая примерная цена?
В личку могу скинуть адрес сайта куда надо эту картинку.
Budget: 500 UAH Deadline: 1 day
Готова помочь
Budget: 300 UAH Deadline: 2 days
Добрый вечер! Скиньте адрес сайта в сообщении
примеры работ: Behance
Budget: 500 UAH Deadline: 2 days
Заинтересован Вашим предложением.
Предлагаю свои услуги.
Общее портфолио
http://vk.com/albums291535830
Подробности почтой
[email protected]
Budget: 500 UAH Deadline: 3 days
Доброе утро.
Готов сделать.
Пишите в личку, скайп или вайбер.
skype: karmakillersl
viber: +38 050 928 69 18
Budget: 300 UAH Deadline: 2 days
Здравствуйте! Буду рада сотрудничеству!
Budget: 500 UAH Deadline: 3 days
Примеры
Budget: 300 UAH Deadline: 2 days
+
Budget: 400 UAH Deadline: 2 days
Пишите, сделаю пару вариантов
Budget: 12345 UAH Deadline: 1 day
стоимость после обсуждения
примеры части работ по ссылкам в профиле
Freelancehunt
e-mail [email protected]
skype titanium-dragon
icq 564810896
Budget: 300 UAH Deadline: 3 days
Здравствуйте! Буду рада сотрудничеству!
Budget: 1111 UAH Deadline: 1 day
это называется эффект двойной экспозиции, а не параллакс
Budget: 200 UAH Deadline: 1 day
готов пытаться вас понять... ))
Budget: 500 UAH Deadline: 1 day
Сделаю утром. Предоставлю несколько вариантов
Budget: 500 UAH Deadline: 1 day
Сделаю сейчас!
Ну хотя бы наройте в инете, примерно то "что хочу". Способ "тыка" ни к чему приличному не приведет )
Design a case model for an electronic device for 3D printing, and also for future use with a syringe press. The case must have openings for USB-A, USB-C, BH-8 connector, display, a hole for an internal reset button, openings for buttons and button pushers. The board can be completely redesigned if your design is more ergonomic. An approximate appearance is shown in the photo.
I wish to create a 3D visualization of the room's interior to understand the comprehensive layout of the furniture and the overall picture after the renovation. I already have all the photos of the furniture elements; they need to be arranged in the space to give the room the appearance it should have after the renovation.
Modification of the STL model of the impeller for 3D printing (PETG)There is a ready STL model of a two-blade propeller for a jet ski SUP board. The geometry of the hub and the seat for the shaft are completely satisfactory, they do not need to be changed.What needs to be done:“Cut off” the old 2 blades from the existing hub.Design 3 new blades from scratch.The radial gap between the edge of the blades and the inner wall of the housing (nozzle) must be strictly 1.5 mm.Technical data for calculating angles and pitch:Motor: Brushless, KV\ 200 (diameter about 50 mm).Power supply: 42 V battery (BMS 60 A).Controller: VESC 75200 V2.The model must be optimized for FDM printing with PETG plastic (strong fillets at the junctions of the blades to the hub).
Good day. The essence of this project is to create product photos for the website. I will provide the approximate style and designs of the houses. I will provide samples of how it should look. Please send samples of your work. And we will collaborate.
3D model of an armrest and foot support (outlined in the photo) is needed for CNC machining armrest 6x6x50 cm Maximum width of the lower part is approximately 11 cm Height 30 cm