Budget: 250 UAH Deadline: 1 day
Сделаю краще, чем в примере.
250 за 1 шт, до 2 часов.
Есть сайт pspb.rudenkowd.com
для каждой категории нужно отрисовать изображение категории
По примеру http://prntscr.com/e55znd http://petro-house.ru/
В ответ цена и срок за одно изображение
Budget: 250 UAH Deadline: 1 day
Сделаю краще, чем в примере.
250 за 1 шт, до 2 часов.
Budget: 200 UAH Deadline: 1 day
Одно изображение - 200 грн
Срок - 4 часа
Budget: 200 UAH Deadline: 1 day
100 грн. Обращайтесь, выполню качественно. [email protected]
Budget: 200 UAH Deadline: 1 day
Здравствуйте! Обращайтесь!
100грн. за шт.
Портфолио в профиле
e-mail: [email protected]
Группа - http://vk.com/design_by_nelly
Budget: 200 UAH Deadline: 1 day
http://richmanstudio.ru/
Behance
Skype: richmanstudio
e-mail: [email protected]
Budget: 200 UAH Deadline: 1 day
Обращайтесь.
Budget: 200 UAH Deadline: 1 day
100 грн - 1 картинка.
2 картинки в день.
Skype: shiftt65
[email protected]
Budget: 200 UAH Deadline: 1 day
От 100 грн. за позицию. Все оговаривается в зависимости от желаемого результата. Мое портфолио: Freelancehunt
Budget: 200 UAH Deadline: 1 day
Здравствуйте. Без проблем выполню Ваш проект. 200 грн. одно изображение. Сроки в зависимости от количества изображений.
Budget: 1000 UAH Deadline: 1 day
2 часа по 100гр. Это если такого качества как на ссылке. За 1 день можно всё закончить.
Budget: 500 UAH Deadline: 1 day
Специализируюсь на моделировании и предметной визуализации. Качественно выполню проект
Budget: 200 UAH Deadline: 1 day
Здравствуйте, Денис!
Я графический и веб дизайнер с опытом 15+ лет.
Цена за каждую такую иллюстрацию 150ргн. и 3-4 часа на каждую (где сначала драфтовый эскиз, после утверждения отрисовка).
Портфолио:
Freelancehunt
Буду рад сотрудничеству.
Skype: art.casper
Budget: 200 UAH Deadline: 1 day
Хочу работать с Вами. 100 грн изображение. В день от 5 шт
Design a case model for an electronic device for 3D printing, and also for future use with a syringe press. The case must have openings for USB-A, USB-C, BH-8 connector, display, a hole for an internal reset button, openings for buttons and button pushers. The board can be completely redesigned if your design is more ergonomic. An approximate appearance is shown in the photo.
I wish to create a 3D visualization of the room's interior to understand the comprehensive layout of the furniture and the overall picture after the renovation. I already have all the photos of the furniture elements; they need to be arranged in the space to give the room the appearance it should have after the renovation.
Modification of the STL model of the impeller for 3D printing (PETG)There is a ready STL model of a two-blade propeller for a jet ski SUP board. The geometry of the hub and the seat for the shaft are completely satisfactory, they do not need to be changed.What needs to be done:“Cut off” the old 2 blades from the existing hub.Design 3 new blades from scratch.The radial gap between the edge of the blades and the inner wall of the housing (nozzle) must be strictly 1.5 mm.Technical data for calculating angles and pitch:Motor: Brushless, KV\ 200 (diameter about 50 mm).Power supply: 42 V battery (BMS 60 A).Controller: VESC 75200 V2.The model must be optimized for FDM printing with PETG plastic (strong fillets at the junctions of the blades to the hub).
Good day. The essence of this project is to create product photos for the website. I will provide the approximate style and designs of the houses. I will provide samples of how it should look. Please send samples of your work. And we will collaborate.
3D model of an armrest and foot support (outlined in the photo) is needed for CNC machining armrest 6x6x50 cm Maximum width of the lower part is approximately 11 cm Height 30 cm