Switch to English version?

Yes

Переключитись на українську версію?

Так

Переключиться на русскую версию?

Да

Przełączyć się na polską wersję?

Tak

Login
Registration
- Welcome to Freelancehunt
  
  Work risk-free, saving time and money
  
  Login Registration

Post your project for free and start receiving proposals from freelancers within minutes after publication!

22 USD

Frame for the installation of straw

22 USD

3D Modeling, Drawings & Diagrams, Engineering

6 out of 6

project complete

publication
open for proposals
terms confirmation
reservation
work underway
project complete

Project translated automatically. Log in or register, to view the original

It is necessary to draw a metallic structure (ram) for the installation of a two-sitting shell + a loot for the loading of the material (flow).The sketch is presented below.In the design should be provided for holes for attachment to the concrete foundation (fundament).The dust should be placed on a substrate under a angle of 16 degrees and rely on the frame in 4 points for 2 bricks in each.The maximum loading height on the substrate, from the charging side should be 3.6 m The minimum loading height of the loading flows (all 3 flows) - 0.9 m, the width of the conveyor bands that will be used to remove the products - 0.8 m.The output holes should not be greater than 0.75 m.The angle of the inclination of the deductive conveys is 18 degrees.The main sizes of the grid, mm:long - 3000width - 1500height - 760 distance between eight stains,in length - 2710v width - 1720Gabrites of stains for the installation of grids (4 stains for 2 grids), mm:length - 290width - 140 distance between eight cylinders for the fixation of grids on the stains - 200width - 15x115x265 It is preferable to use the cheapest variants of European sorting.For example, swellers, corners and so on.The design should be as simple as possible in manufacturing.The European sorting profiles are below at the link: http://sections.arcelormittal.com/ru/tovary-i-uslugi/assortiment.html The project is required in the form of an edited file in autocad or solidworks, in order for its possible further correction, supplementation, etc.

Applications 1

Application viewing is only available registered users.

Client's review of cooperation with Anatolii Koshevetskyi

Quality

Professionalism

Cost

Contactability

Deadlines

The work was performed at a high level in the agreed time, despite the introduction of additional requirements to the resulting project in the process of work.

Denis Grishan | Safe

Freelancer's review of cooperation with Denis Grishan

Payment

Task setting

Clarity of requirements

Contactability

A good customer knows what he wants. There was no problem with payments. I recommend, though I would like to work with him myself.

Anatolii Koshevetskyi | Safe

Proposals 2

by default date online rating cost completion time

Winning proposal22 USD

Anatolii Koshevetskyi

163

Winning proposal22 USD

The estimate of the cost was sent by mail.
Half of the work is actually done.
I can give up a little.
Yes . Add to the topic of the project section "Engineering"

Show original

Translate

1 June 2018, 11:45

27 USD

Aleksandr Sergeich

147 9

27 USD

I do it.
Cost and time - after clarification of the TZ.
Go to turn.
and ........................
by qwerity.jimdo.com

Show original

Translate

30 May 2018, 22:00

Current freelance projects in the category 3D Modeling

Need an engineer for numerical modeling (ANSYS Autodyn / LS-DYNA) We are looking for a specialist to carry out project work on numerical modeling of transient dynamic processes. At the first stage, it is necessary to assess the feasibility of performing calculations, determine the scope of work, and form the project cost. Detailed technical… 3D Modeling, Engineering ∙ 8 hours 12 minutes back ∙ 1 proposal
Problems with displaying textures of 3D files on Sketchfab 16 USD Can you tell me why the textures of my 3D files are not displaying and why I have white walls when uploading them to Sketchfab? This happens with any blend, fbx, or glb file; I am working in Blender, version 5.0. I have already clicked on Pack resources or Make paths… 3D Modeling, Web Programming ∙ 9 hours 30 seconds back ∙ 3 proposals	16 USD
Make a photo render of the product in SolidWorks 22 USD Hello, there are devices designed in SolidWorks, and it is necessary to create photo renders from different angles. The file format is STEP. The product has straps that need to be shown in a fastened position (bent). 3D Modeling ∙ 15 hours 38 minutes back ∙ 5 proposals	22 USD
3D model of the part according to the sketch in format A precise 3D model of a metal part is required based on a hand sketch. The main requirement is that the finished file must be strictly in STEP-AP242 format (with tolerances and roughness) for CNC. 3D Modeling, Mechanical Engineering & Instrument Making ∙ 16 hours 48 minutes back ∙ 11 proposals
Development of the design and layout of the Fesco Ultra POS stand for printing/cutting It is necessary to develop the design and a ready layout for printing/cutting a tabletop POS stand for the Fesco Ultra brand. The stand will be used for presenting the brand's products: toothpaste, toothbrushes, dental floss, and floss picks. We provide approximate references… 3D Modeling, Industrial Design ∙ 21 hours 21 minutes back ∙ 4 proposals

Denis Grishan

Ukraine 1

Frame for the installation of straw

Client's review of cooperation with Anatolii Koshevetskyi

Freelancer's review of cooperation with Denis Grishan

Current freelance projects in the category 3D Modeling

Need an engineer for numerical modeling (ANSYS Autodyn / LS-DYNA)

Problems with displaying textures of 3D files on Sketchfab

Make a photo render of the product in SolidWorks

3D model of the part according to the sketch in format

Development of the design and layout of the Fesco Ultra POS stand for printing/cutting