Proposal for Arduino.
22 USD
Everything is great. I hope we will cooperate further.
Proposals concealed
The list does not show proposals concealed by the client or freelancer with a Plus profile, as well as proposals violating rules
Proposals are currently absent
Freelancers are reviewing the task — proposals will appear here soon.
-
Oleg Pilshikov 3 February 2020Здравствуйте, Ирина. У вас есть исходник старого проекта, или нужно писать заново?
-
Irina Snitko
3 February 2020
Исходник есть
-
Oleg Pilshikov 3 February 2020
Для добавления в схему аккумуляторов, их и другие электронные модули вы хотите чтоб я добавил в стоимость работ, либо будете сами покупать и делать?
-
Irina Snitko
3 February 2020
Покупать и делать буду сам, нужна только рекомендация по подбору и схема куда и как правильно подключить. На данный момент ориентируюсь на вот такие компоненты, но на счет зарядного не уверен. АКБ тоже может быть другой, но емкость не менее 8000-10 000 и обязательно плоский.
https://www.rcscomponents.kiev.ua/product/9059156m15-3-7v-10000mah-pcb-akkumulyator-litij-polimernyj_52598.html
https://www.rcscomponents.kiev.ua/product/zaryadnoe-dlya-li-po-s-zaschitoj-tp4056-1a-lipo-battery-charging-board_101154.html
-
Oleg Pilshikov 3 February 2020
зарядное - отлично подходит, аккумуляторы с планшета взять, если плоские нужны
-
Irina Snitko
3 February 2020
Значит аккумулятор я сам поставлю, не проблема, возможно порекомендуете еще какой то индикатор уровня заряда из готовых. Тогда вся задача сводится к доработке только программного кода.
-
Oleg Pilshikov 3 February 2020
Пишите в личку...
Current freelance projects in the category Embedded Systems & Microcontrollers
212 USD
3 proposals
need a specialist who understands OpenWRT firmware, need to configure the router for geocomply OpenWRT Specialist Custom Firmware Developer Router Firmware Engineer
Not specified
2 proposals
Development of firmware deployed on the gateway and management of direct interaction with PLC/equipment in the technical room (Modbus, BACnet, etc.).
Business Safe
Ground control station based on SINE LINK
581 USD
3 proposals
It is necessary to integrate the NCS with the automatic launch system (catapult with a microcontroller) to transmit a signal to the microcontroller, which will initiate the operation of the catapult 500 meters away from it.
Business Safe
DRONE AIRCRAFT TYPE
6702 USD
4 proposals
Create compatibility between the ground control station, automatic start system (SAS), radar, and the aircraft.
79 USD
7 proposals
It is necessary to refine the existing Bitclock rev3 PCB in KiCad. Project sources: https://github.com/goat-hill/bitclock/tree/master/bitclock-pcb/rev3a/kicad Task: 1. Change the size and shape of the board to fit the new STEP/3D model of the case. 2. Move/replace the current power connector with USB-C. 3. Redesign the monitor connection port to an 8-pin connector. 4. Arrange components so that the board fits correctly into the case according to the mounting points. 5. Preserve the existing functionality of the board. 6. Check the alignment of the board with the 3D/STEP model. 7. The output should include ready KiCad files + updated 3D model/fit check. Main requirement: a specialist in KiCad/PCB design is needed, who can work with STEP cases and mounting points.
Loading...
Loading...