Modernization of equipment
111 USD You need to make the following changes:
1 .The downward direction disappears from the load
The 2ndA small distance between the directors that creates a wire for additional load on the lower directors and during this platform drive
3 .Change the cover of the corpus on the whole flexible leaves (there are sketches)
and 4.The block of the rolls disappears.
and 5.Val of the reducer through the platform hanging, creates load and deforms the tooth reck
6 .The size of the upper block has a large radius.
7 .The square is shrinking when loaded in 80 kg, you need to remove
The data of observation is superficial and carries a change in the design.The basic requirements for the design are the combination of simple manufacturing and relative reliability.
The objective of the project is to get a 3D model, installation schemes in two options of fixing and drawing for cutting and collection in PDF and DXF formats, 4-5 photos desired in a render, a real receiver with consideration of notes.Link to download the model and drawings https://fex.net/ru/s/r1froy7
Applications 7
Client's review of cooperation with Oleg Boguslavsky
Modernization of equipmentVery interesting proposals, 100% satisfied with the work.
Freelancer's review of cooperation with Dmitro Bakreu
Modernization of equipmentA quiet and seductive client. He understands well what he does.
Hears the executive. All questions are resolved quickly. Payment is timely.
I hope for further cooperation.
-
10 days223 USD
247 2 0 10 days223 USD
The first thing I will do is calculate hardness and strength. That it did not disappear.”
Check out the outbreak:
the downward direction;
Block of rollers;
The load is 80 kg.
Transfer of loads to the wave of the reductor.
If 80 kg is the mass to raise, the dynamic coefficient should be taken into account at least 1.5. A minimum load of 120 should be accepted. (When the elevator starts, we become a bit harder.)
When you see slides and tensions, you can do a 3-D model.
If you don’t make a calculation, then you’ll publish another project because something is going to go somewhere.
… Or if you exaggerate with strength - you’ll bear excessive losses because of the fact that you could have taken smaller profiles.
-
28 days356 USD
3842 47 2 28 days356 USD
Good evening . I have a great experience in modernizing non-standard equipment. ( see profile ) I will create a new model, replace the load, release a new set of drawings. Nuances of the design in the process of ordering.
-
14 days223 USD
527 8 0 14 days223 USD
The link is broken (incomplete) assembly / there is no fixation, broken links to details/.
Repeat the model for its review.
The deadlines and amounts will be specified after possible opening the collection.
-
12 days223 USD
652 9 0 12 days223 USD
Price indicated for the introduction of directions, the preparation of the CD (PDF+DXF), 4-5 render, schemes in composite/disclosed state
-
знову цей підйомник...
-
Добрий вечір. Так підйомник такий самий, у попередньому проекті не мав змоги обрати виконавця
-
Перше, що зроблю – це розрахунок на жорсткість та міцність. «Щоб не прогиналося.»
Перевірю прогини:
-направляючої нижньої;
- блок роликів;
- площадки від навантаження 80 кг.
- передача навантажень на вал редуктора.
Якщо 80 кг це маса, яку треба підняти, - треба врахувати коефіцієнт динаміки як мінімум 1,5. Тобто розрахункове навантаження мінімум 120 треба прийняти. (коли ліфт стартує, ми стаємо трохи важчими).
Коли побачите прогини, і напруги, можна робити 3-д модель.
Якщо не зробите розрахунок, то будете публікувати ще один проект, бо десь щось гнеться.
Або якщо перебільшите з міцністю – будете нести зайві трати, через те, що можна було прийняти менші профілі.
-
Current freelance projects in the category Drawings & Diagrams
Architect for working with point cloudsOrder: 3D Modeling of Facade Cladding and Parapets Based on Point Cloud (BIM / CAD) I am looking for an experienced designer / 3D modeler who will create an accurate geometric model of the facade cladding and roof/parapet area based on the provided point cloud (laser… Drawings & Diagrams, Object Design ∙ 2 hours 22 minutes back ∙ 2 proposals |
Person to create a point cloud of the buildingLocation: Lubin Object type: Aquapark Scope of work: I am looking for an experienced company or freelancer to perform comprehensive 3D laser scanning of the building. The assignment includes: Performing ground scans outside the building. Registering and stitching scans into… Drawings & Diagrams, Object Design ∙ 2 hours 36 minutes back |
Make calculations and sketches of drawings regarding the slopes on the roof
22 USD
It is necessary to lay out the elements of slopes 1000*500 on the roof from the lowest height to the highest, highlighting the elements in different colors for visual appearance for the installer, and add the specification of the elements. The result of the elements can be… Architectural Design, Drawings & Diagrams ∙ 3 hours 48 minutes back ∙ 1 proposal |
Development of KMD based on the completed projectAccording to the completed project for the separation of floors, it is necessary to develop detailed drawings in KMD for manufacturing at the factory. The project is available in PDF and DWG. Object Design, Drawings & Diagrams ∙ 1 day 6 hours back ∙ 6 proposals |
Develop metal structures for roofs on entrance groups
67 USD
It is necessary to develop metal frames for roofs over entrance groups (entrance group 1 - roof over the gate, entrance group 2 - roof over the gate with a door), specifically: supports for the roof metal structure, the metal structure of the roof itself, materials, fastening… Drawings & Diagrams ∙ 2 days back ∙ 7 proposals |
Mykolaiv