Drawings and material list. For a canopy for the installation of solar panels. A canopy for storing equipment and vehicles. Installation site: s. Zhemchuzhnoe, Pavlohrad district, Dnipropetrovsk region, angle of about 10 degrees. Long panels 620 (230 by 113), needed in two rows about 19 meters in length available. So a frame is needed for the installation of the panels only without covering; the joints of the panels will be sealed later with rubber gaskets. It should withstand wind and snow loads. It is not standing in an open field, there are small buildings nearby, but it is outside the city and on a decent slope. A galvanized mounting profile has already been ordered, with a thickness of 1.4 mm, and it needs purlins about 1 m. So, it will probably be necessary to install a profile pipe to reinforce it, to reduce the number of beams, I think, to minimize deflection. It was planned for installation on the roof, but the roof turned out to be not quite convenient for such installation.
A working project for a wooden two-story frame with a total area of 144 sq m is required. The grid is located in a column layout of 6x6 meters. The ceiling height is 7.2 m. The purpose of the frame is for individual storage rooms. The load is 300 kg per m2.
Detailed plan for two plots for construction near the lake in Volyn region, Kovel district, village of Hlukhi. Two modular houses, utilities, solar panels, recreation areas, etc.
Wooden terrace 7x4.5m with a frame wooden sauna 3.5x2.25m and a tub. The terrace is located on a plot with a slight slope. It is necessary to calculate the structure of the terrace (made of wood; the site is in the mountains - high snow load), calculate the structure of the sauna, develop a 3D model (photorealistic renders are not needed) and prepare drawings (facades, sections, site plan). A small complication: the documentation and drawings must comply with a specific format. Nothing special, but markings, colors of materials, and other details must adhere to a certain format. I will provide samples. In the attached files, there is an unfinished model for a general understanding of the concept.
# Requirements Specification — USB-C PD → 4× USB-C 5V Power Distribution Board for 5G Modem Sled Purpose and Scope A single PCB that receives power from a single consumer USB-C PD power bank with a capacity of 100–200 W and distributes stabilized 5 V through up to four USB-C ports solely for power. Each port powers the auxiliary power input of one M.2 Key-B (NGFF) modem sled with an installed 5G module Quectel RM520N-GL or RM505Q. The board provides only power — USB data connections of the modems with the host pass through the sled's own USB connectors and are not included in the scope of this specification. I am not familiar with typical budgets for such projects, so please propose your budget.
I need to create a coffee island project as quickly and clearly as possible so that it can be handed over to specialists for construction. Before starting, we need to talk somewhere on Discord or just via video call so that I can provide as much information as possible. Priority will be given to candidates who know the specifics of this business/have already done something similar to my request. Have a great day, Olexiy.
A drawing of a double-pitched truss with parallel chords made of profile pipe is needed. Detailing of the corner cuts of the blanks is required.
it is necessary to design and prepare drawings of the workspace (workbench, wall, and shelf). sheet metal 1.5 mm prepare files for laser cutting prepare drawings for bending there are also additional projects
It is necessary to make notes in AutoCAD on the completed project, as well as to add a table to the project based on the completed work reports.
I am looking for a specialist (AutoCAD / Visio / Illustrator / CorelDRAW) to create professional, aesthetic, and engineering-precise 2D/3D diagrams of water purification systems (domestic and industrial). The diagrams will be used in Commercial Proposals for clients. An example of the desired detail and style is attached in the file (add your photo). *One drawing needs to be made: Check valve at the inlet; Inlet buffer tank; Pump with automation after the tank; Big Blue 20" mechanical filter (with pressure gauges at the inlet and outlet, and bypass); Filtration column with automatic control valve without tank; Filtration column with automatic valve and salt tank; Industrial reverse osmosis; Mineral dosing station; Accumulation tank of purified water 1000 liters; Pump with automation for supplying purified water; Big Blue 20" carbon filter; Ultraviolet lamp *Highlight or label with the directions of water flow all types of water. Inlet water, Drain to sewage, Purified water *Show the drain to sewage from No. 5, No. 6, No. 7 *Show small overflow pipes from all tanks, salt tank *Depict the sampling tap after each column and reverse osmosis Main requirements for execution and detailing:1. Language and design Language of inscriptions: Ukrainian (all labels: “Inlet of raw water”, “Outlet of purified water”, “Discharge to sewage”, etc.). Style: Neat, vector, maintained in a modern technical style (vector or semi-volume elements of equipment). Output formats: PNG with a transparent background (high resolution). PDF for printing/inserting into KP. Source file (DWG, AI, CDR or Visio).
A project needs to be developed for a large park composition in the shape of a cat and a mouse based on the attached visual reference. The figures will be installed outdoors in the park area and will serve as a decorative art object and photo zone. The base of the figures should be made of a sturdy metal frame. The outer covering is planned to be made of artificial grass or another weather-resistant material. Approximate dimensions of the cat: — total length — 8 m; — height of the head — 3.24 m; — height at the withers — 2.34 m; — width of the body — 2.4 m; — length of the head — 1.8 m. Approximate dimensions of the mouse: — total height — 1.8 m; — body length — 0.81 m; — height at the withers — 1 m; — total width with ears — 0.9–0.95 m. What is required from the performer: Develop an artistic 3D model of the two figures while adhering to the specified dimensions and proportions. Prepare visualizations from several angles. Design the internal supporting metal frame. Plan for dividing the large figure into modules for manufacturing, transportation, and assembly. Prepare working drawings of the metal structure with dimensions, profile cross-sections, connection nodes, and attachment points. Develop a method for securing the structure to a concrete base or foundation. Consider wind, snow, and operational loads. Provide specifications for the metal and the approximate weight of the structure. Provide recommendations for anti-corrosion protection, external covering, delivery, and assembly. The figures will be permanently outdoors, so the structure and covering must be resistant to rain, snow, frost, sun, and temperature fluctuations. Formats of the result: — 3D model in STEP, SolidWorks, Blender, or another agreed format; — drawings in PDF and DWG/DXF; — material specifications in PDF or Excel; — renders in JPG/PNG. We are looking for not just a 3D visualizer, but a specialist or team with experience in designing real metal structures. In your proposal, please indicate: — the cost of 3D modeling; — the cost of engineering design and drawings; — timelines for completion; — the software in which the work will be done; — examples of similar projects; — whether you can also organize manufacturing and assembly. The images are a reference. The final design can be adapted and made original.
Title: Development of electrical schematics (EasyEDA) for data acquisition modules (STM32, precision ADC, galvanic isolation) Task Description: We are looking for an experienced circuit engineer to develop the schematic diagrams for two boards (PCB design is not required at this stage). What needs to be designed: Master module: power input of 24V and communication with the external world via hardware-isolated RS-485. Analog input module: digitization of two channels of industrial sensors (0-10V / 4-20mA). Based on a precision ADC (type ADS1248). A mandatory condition is the presence of an internal digital isolation barrier after the ADC. The boards communicate with each other via SPI. Key requirements (Strict!): Environment: only EasyEDA (Pro or Std). Components: 100% of parts must have part numbers (C-parts) from the LCSC Electronics catalog, as the boards will go for automated PCBA. Base MCU: STM32F103 (or your suggestions for modern equivalents). A detailed, well-written technical specification with a ready reference architecture from Texas Instruments will be provided to the candidate. Bonus: For the specialist who diligently and competently completes this stage (circuit design), a second paid stage — routing of these printed circuit boards (PCB Design) — will be guaranteed.
Execute the drawing according to the sketch while preserving it in the standard PDF format. The dimensions, placement, and margins should remain as they are.
Good day! We are the pharmacy network Med-service. For the premises for a pharmacy in Irpin, we need to carry out work on preparing the initial data for the development of architectural and computer design sections (AutoCAD), namely: Creating a measurement drawing of the facade and entrance group (porch) with photo documentation; Conducting measurements of the premises indicating: marks and differences in ceiling heights; marks and differences in floor levels; dimensions of window and door openings; thickness of reveals, walls, and partitions; Marking all engineering communications on the plan with references, including: electrical panels; electricity and water meters; sewer risers; water supply pipes; inspection hatches; air conditioners and other equipment; Preparing a detailed photo report. Examples of work are attached. We are ready to consider proposals for cooperation.
Development of a technical plan for sockets and switches based on the ready-made furniture drawing (Rivne / remotely). Hello! I am looking for a design engineer or technical draftsman to develop an electrical scheme for builders. What is available: An accurate drawing of the rooms with wall dimensions. Approved furniture and plumbing layout plan (where everything is placed). No 3D visualizations. What specifically needs to be done (Technical requirements): Socket and switch plan: Place points in relation to the dimensions of furniture and appliances. Specification by type (moisture protection): Clearly indicate the type of sockets for wet areas (for example, moisture-proof with grounding and IP44 covers for the bathroom). Calculation of power lines (cables): Highlight and specify power points that require a separate cable of increased cross-section (for example, for the cooktop, oven, powerful boiler) and separate lines for appliances like the extractor fan. Switch scheme: Consider convenient light control (three-way switches, linking to lighting groups). Result: A finished drawing in PDF format with accurate dimensions, clearances from walls/furniture, and technical notes for installers. Please indicate the cost of your work (for the entire project or per sq.m) and estimated completion time? 120 kV. Thank you!